China Good quality Energy Saving Rotary Screw Air Compressor Manufacturer air compressor oil

Product Description

KY-200KYG Air Compressor (can be customized) :

GENERAL FEATURES:
Permanent magnet inverter compressor because of its energy saving and high efficiency has become a hot and bright spot of the industry, the original air compressor energy consumption on the market, is gradually being the permanent magnet inverter compressor to replace or replacement, users can directly bring cost saveing of 20%-40%.
With the development of science and technology, air compressor is widely used in many industries such as machinery, metallurgy, building materials, electric power, chemical industry, food, textile and so on. However, the air compressor belongs to the high energy consumption equipment, power consumption in some industries accounted for more than 30% og the power consumption of production, it is commonly known as “electric tiger”.
SPECIAL FEATURES:
1,AIR PRESSURE STABILLTY
Due to the use of screw air compressor variable frequency stepless speed regulation characteristics of inverter, inverter controller or regulator through internal PID, can smoothly start; on consumption volatility is relatively large occasions, and can quicklyh adjust the response. Compared with the upper and lower limit switch control of the power frequency operation, the air pressure stability increases exponentially.
2,START NO IMPACT
Because the transducer itself contained the function of soft starter, starting current within the maximum rated current of 1.2 times, compared with the start frequency in general more than 6 times the rated current, start a little impact.
This impact is not only on the grid, the impact of the entire mechanical system, but also greatly reduced.
3,VARIABLE FLOW CONTROL
Power driven air compressor can only work in an exhaust, inverter air compressor can work in a wide range of exhaust. Frequency converter is based on the actual use of gas in real time to adjust the motor speed to control the amount of exhaust.
When the air volume is low, the air compressor can be automatically dormant. thereby greatly redcing the energy loss. The optimized control strategy can further improve the energy saving effect.
4,AC POWER SUPPLY VOLTAGE BETTER
Because of the over modulation technology of the inverter, the output voltage of the motor can be output when the voltage of the AC power supply is low, and the voltage of the output to the motor is too high.
For the generation of power, frequeucy conversion drive can show its advantages.
5,AC POWER SUPPLY VOLTAGE BETTER
Most of the working condition of the frequency conersion system is lower than the rated speed of the work, the host machine noise and wear down, prolongmain- tenance and service life.
If the fan is also driven by frequency conversion, can significantly reduce the nosie of air compressor work.

TECHNICAL PARAMETERS:

Model	Power	Pressure (Mpa)	Air flow	Noise	Stage	Exit pipe diameter	Weight (KG)	Dimensions (mm(LxWxH)
PE-10AVF	7.5	8	1.0	60±2	Single grade	3/4	280	1000600100
		10	0.8
PE-20AVF		8	2.2	60±2	Single grade	1	480	11508001280
		10	1.8
PE-30AVF	22	8	3.8	62±2	Single grade	11/4	520	11508001280
		10	3.0
PE-40AVF	30	8	5.0	63±2	Single grade	11/4	550	11508001280
		10	4.4
PE-50AVF	37	8	6.8	63±2	Single grade	11/2	650	130010001450
		10	5.4
PE-60AVF	45	8	8.0	65±2	Single grade	11/2	750	130010001450
		10	6.8
PE-75AVF		8	9.7	65±2	Single grade	2	1200	170012701500
		10	8.6
PE-100AVF	75	8	13.2	65±2	Single grade	2	1350	170012701500
		10	16.1

ENERGY-SAVING EFFECT OF TWO-STAGE COMPRESSION:

According to the engineering thermodynamics theory, it is the most economical for the compressor with isothermal compres-
sion.Two-stage oil-injection screw air compressor is designed based on the above theory, it fully improves the cooling function through oil injection during the two-stage compression, plus the inter-stage cooling, by ensuring the temperature is above the pressure dew point, it can be close to isothermal compression as possible, so as to achieve the energy-saving effect.
At the same time, due to low compression ratio of the two-stage airend, the “internal leakage”is largely reduced in the compression process compared with the single-stage compression airend with the same power and same discharge pressure.On the contrary, the diplacement is increased, which means that the efficiency is increased, and the specific power is reduced.
Compared with the ordinary two-stage permanent magnetic compressor on the market,Moair uses the two-drive and two-stage compres- sion, which directly avoids the power loss inside the gear set.
Energy-saving advantages:
1,To reduce the bearing load, and improve the volumetric efficincy;
2,In the case of partial load operation, it can improve efficiency and become energy saving to a better extent.
3,The energy saving of two-stage screw air compressor is up to 15%-25% than that of the one-stage air compressor, which can save the considerable electricity fees every year.

About shipping

Company information

Why choose us?

Certificate

FAQ:

1.Q:What do you need machine and quotation?

A: According to capacity and factory size ,we can give you details.

2.Q: Are you trading company or manufacturer ?

A:We are factory.

3.Q:How do we pack machine?

A:Exporting wooden cases

4.Q:Lead time

A:Around 25-30 days after the receipt of your deposit.

Type:	High Pressure Gun
Usage:	Paint Spray Gun, Washing Gun, Hopper Gun, Garden Gun
Working Style:	Rotary Type
Air Wrench Type:	Pulse pneumatic wrench
Pneumatic Drill Range:	Tunnel
Degree of Automation:	Automatic

Customization:	Available \|

air compressor

What are the advantages of using an air compressor in construction?

Using an air compressor in construction offers numerous advantages that contribute to increased efficiency, productivity, and versatility. Here are some key benefits of using air compressors in construction:

Powering Pneumatic Tools: Air compressors are commonly used to power a wide range of pneumatic tools on construction sites. Tools such as jackhammers, nail guns, impact wrenches, drills, and sanders can be operated using compressed air. Pneumatic tools are often preferred due to their lightweight, compact design and ability to deliver high torque or impact force.
Efficient Operation: Air compressors provide a continuous and reliable source of power for pneumatic tools, allowing for uninterrupted operation without the need for frequent battery changes or recharging. This helps to maintain a smooth workflow and reduces downtime.
Portability: Many construction air compressors are designed to be portable, featuring wheels or handles for easy maneuverability on job sites. Portable air compressors can be transported to different areas of the construction site as needed, providing power wherever it is required.
Versatility: Air compressors are versatile tools that can be used for various applications in construction. Apart from powering pneumatic tools, they can also be utilized for tasks such as inflating tires, cleaning debris, operating air-operated pumps, and powering air horns.
Increased Productivity: The efficient operation and power output of air compressors enable construction workers to complete tasks more quickly and effectively. Pneumatic tools powered by air compressors often offer higher performance and faster operation compared to their electric or manual counterparts.
Cost Savings: Air compressors can contribute to cost savings in construction projects. Pneumatic tools powered by air compressors are generally more durable and have longer lifespans compared to electric tools. Additionally, since air compressors use compressed air as their power source, they do not require the purchase or disposal of batteries or fuel, reducing ongoing operational expenses.
Reduced Electrocution Risk: Construction sites can be hazardous environments, with the risk of electrocution from electrical tools or equipment. By utilizing air compressors and pneumatic tools, the reliance on electrical power is minimized, reducing the risk of electrocution accidents.

It is important to select the appropriate air compressor for construction applications based on factors such as required air pressure, volume, portability, and durability. Regular maintenance, including proper lubrication and cleaning, is crucial to ensure the optimal performance and longevity of air compressors in construction settings.

In summary, the advantages of using air compressors in construction include powering pneumatic tools, efficient operation, portability, versatility, increased productivity, cost savings, and reduced electrocution risk, making them valuable assets on construction sites.

air compressor

What safety precautions should be taken when working with compressed air?

Working with compressed air requires adherence to certain safety precautions to prevent accidents and ensure the well-being of individuals involved. Here are some important safety measures to consider:

1. Personal Protective Equipment (PPE):

Wear appropriate PPE, including safety goggles or a face shield to protect eyes from flying debris or particles, hearing protection to reduce noise exposure, and gloves to safeguard hands from potential hazards.

2. Compressed Air Storage:

Avoid storing compressed air in containers that are not designed for this purpose, such as soda bottles or makeshift containers. Use approved and properly labeled air storage tanks or cylinders that can handle the pressure and are regularly inspected and maintained.

3. Pressure Regulation:

Ensure that the air pressure is regulated to a safe level suitable for the equipment and tools being used. High-pressure air streams can cause serious injuries, so it is important to follow the manufacturer’s recommendations and never exceed the maximum allowable pressure.

4. Air Hose Inspection:

Regularly inspect air hoses for signs of damage, such as cuts, abrasions, or leaks. Replace damaged hoses immediately to prevent potential accidents or loss of pressure.

5. Air Blowguns:

Exercise caution when using air blowguns. Never direct compressed air towards yourself or others, as it can cause eye injuries, hearing damage, or dislodge particles that may be harmful if inhaled. Always point blowguns away from people or any sensitive equipment or materials.

6. Air Tool Safety:

Follow proper operating procedures for pneumatic tools. Ensure that tools are in good working condition, and inspect them before each use. Use the appropriate accessories, such as safety guards or shields, to prevent accidental contact with moving parts.

7. Air Compressor Maintenance:

Maintain air compressors according to the manufacturer’s guidelines. Regularly check for leaks, clean or replace filters, and drain moisture from the system. Proper maintenance ensures the safe and efficient operation of the compressor.

8. Training and Education:

Provide adequate training and education to individuals working with compressed air. Ensure they understand the potential hazards, safe operating procedures, and emergency protocols. Encourage open communication regarding safety concerns and implement a culture of safety in the workplace.

9. Lockout/Tagout:

When performing maintenance or repairs on compressed air systems, follow lockout/tagout procedures to isolate the equipment from energy sources and prevent accidental startup. This ensures the safety of the individuals working on the system.

10. Proper Ventilation:

Ensure proper ventilation in enclosed areas where compressed air is used. Compressed air can displace oxygen, leading to a potential risk of asphyxiation. Adequate ventilation helps maintain a safe breathing environment.

By adhering to these safety precautions, individuals can minimize the risks associated with working with compressed air and create a safer work environment.

air compressor

Can air compressors be used for automotive applications?

Yes, air compressors can be used for various automotive applications and are commonly found in automotive repair shops, garages, and even in some vehicles. Here are some automotive applications where air compressors are frequently utilized:

1. Tire Inflation: Air compressors are commonly used to inflate tires in automotive applications. They provide a convenient and efficient way to inflate tires to the recommended pressure, ensuring optimal tire performance, fuel efficiency, and safety.

2. Air Tools: Air compressors power a wide range of pneumatic tools used in automotive repair and maintenance. These tools include impact wrenches, ratchet wrenches, air hammers, pneumatic drills, and sanders. Air-powered tools are favored for their high torque and power-to-weight ratio, making them suitable for heavy-duty automotive tasks.

3. Spray Painting: Air compressors are commonly used in automotive painting applications. They power airbrushes and spray guns that are used to apply paint, primer, and clear coats. Air compressors provide the necessary air pressure to atomize the paint and deliver a smooth and even finish.

4. Brake System Maintenance: Air compressors play a crucial role in maintaining and diagnosing automotive brake systems. They are used to pressurize the brake lines, allowing for proper bleeding of the system and detection of leaks or faults.

5. Suspension Systems: Some automotive suspension systems, such as air suspensions, rely on air compressors to maintain the desired air pressure in the suspension components. The compressor inflates or deflates the suspension as needed to provide a comfortable ride and optimal handling.

6. Cleaning and Dusting: Air compressors are used for cleaning automotive parts, blowing away dust and debris, and drying surfaces. They provide a high-pressure stream of air that effectively cleans hard-to-reach areas.

7. Air Conditioning Systems: Air compressors are a key component in automotive air conditioning systems. They compress and circulate refrigerant, allowing the system to cool and dehumidify the air inside the vehicle.

When using air compressors for automotive applications, it’s important to consider the specific requirements of the task at hand. Ensure that the air compressor has the necessary pressure and capacity to meet the demands of the application. Additionally, use appropriate air hoses, fittings, and tools that are compatible with the compressor’s output.

Overall, air compressors are versatile and valuable tools in the automotive industry, providing efficient power sources for a wide range of applications, from tire inflation to powering pneumatic tools and supporting various automotive systems.

China Good quality Energy Saving Rotary Screw Air Compressor Manufacturer air compressor oil
editor by CX 2023-10-09

China best New-DC12V Portable-Li-ion Battery Cordless/Electric-Air Pump/Compressor/Tire Inflator Car Automobile Accessories-Power Tools air compressor repair near me

Product Description

Stride Across Tools ITCAP318U -12V USB Charger Portable Lithium-Ion(2200mAh) Battery Cordless Air Inflator/Compressor For Car/Bicycle Tires,Balls ,Swimming Rings,Toys …

Certifications :GS/CE/EMC/ROHS/UL/PSE.

Product Name:	Li-Ion Battery Cordless Air Inflator /Compressor
Battery Power &Voltage:	2200mAh Lithium-Ion ;12V
Outermost Shell :	Strong Stainless Steel Painting
Max .Air Pressure:	150PSI(10BAR)
Automatic Shutdown Function :	After 60seconds ,Machine will be Automatic shutdown
Initial Detection Of Pressure :	3PSI
Battery Charger:	USB Charger&Car Cigar Lighter Chargers Included !
Battery Charging Time :	5-6hours
LED Torch:	With Super Bright LED Light
Machine Net Weight:	0.8kgs
Recommend Packing Type:	Stronger I-Phone Box Packing
Accessories :	5pcs Different kinds of air Inflation Nozzles ,USB Battery Charger 1pc .

Features &Descriptions :

Tyre Inflator Cordless: The cordless and compact tire inflator is easy to carry and it can be operated with one hand at weightes only 0.8kgs . The LCD screen displays real time pressure, so you can monitor the pressure without bending down to check the bottom.
Large-capacity 2200mAh Lithium-Ion battery: This portable air compressor pump has built-in certified rechargeable lithium-ion Battery Capacity 2200mAh Powerful and super convenient Chargers of USB Wire Cable Charger is offering you the most convenient with charging conditions even during your travels by car .
Preset tire pressure, fast automatic inflation: The tire inflator has 4 switchable pressure units, namely PSI, BAR, KPA, KG/CM², you can preset the tire pressure to the desired pressure of the tire and at any time test tire pressure. When the inflation reaches the preset value, the pump will automatically shut down to avoid over-inflation.
Multi -purpose: The highest inflation pressure is 150psi(10bar), suitable for cars, motorcycles, balls, inflatable swimming pools, swimming rings, inflatable toys, etc., compatible with more than 90% of inflatable products on the market.
Night use: When the inflatable power button is activated, the LED lights / CHINAMFG will automatically light up. Very convenient for emergency lighting in the dark. The LCD digital display with backlight is easy to read even when inflated at night. The LED light can also be turned on when not inflated, used alone as a flashlight.

After-sales Service:	Professional Service Team After Sales
Warranty:	1 Year Warranty Term
Certification:	RoHS, CE, GS,EMC,PSE,UL
Voltage:	12V
Max Pressure:	150psi(10bar)
Charger Type:	USB Wire Cable Charger

Samples:	US$ 100/Piece 1 Piece(Min.Order) \| Request Sample

Customization:	Available \|

air compressor

Can air compressors be used for painting and sandblasting?

Yes, air compressors can be used for both painting and sandblasting applications. Here’s a closer look at how air compressors are utilized for painting and sandblasting:

Painting:

Air compressors are commonly used in painting processes, especially in automotive, industrial, and construction applications. Here’s how they are involved:

Spray Guns: Air compressors power spray guns used for applying paint coatings. The compressed air atomizes the paint, creating a fine mist that can be evenly sprayed onto surfaces. The pressure and volume of the compressed air impact the spray pattern, coverage, and overall finish quality.
Paint Mixers and Agitators: Compressed air is often used to power mixers and agitators that ensure proper blending of paint components. These devices use the compressed air to stir or circulate the paint, preventing settling and maintaining a consistent mixture.
Airbrushing: Air compressors are essential for airbrushing techniques, which require precise control over airflow and pressure. Airbrushes are commonly used in artistic applications, such as illustrations, murals, and fine detailing work.

Sandblasting:

Air compressors play a crucial role in sandblasting operations, which involve propelling abrasive materials at high velocity to clean, etch, or prepare surfaces. Here’s how air compressors are used in sandblasting:

Blasting Cabinets: Air compressors power blasting cabinets or booths, which are enclosed spaces where the sandblasting process takes place. The compressed air propels the abrasive media, such as sand or grit, through a nozzle or gun, creating a forceful stream that impacts the surface being treated.
Abrasive Blasting Pots: Air compressors supply air to abrasive blasting pots or tanks that store and pressurize the abrasive media. The compressed air from the compressor enters the pot, pressurizing it and allowing for a controlled release of the abrasive material during the sandblasting process.
Air Dryers and Filters: In sandblasting applications, it is crucial to have clean, dry air to prevent moisture and contaminants from affecting the abrasive blasting process and the quality of the surface being treated. Air compressors may be equipped with air dryers and filters to remove moisture, oil, and impurities from the compressed air.

When using air compressors for painting or sandblasting, it is important to consider factors such as the compressor’s pressure and volume output, the specific requirements of the application, and the type of tools or equipment being used. Consult the manufacturer’s guidelines and recommendations to ensure the air compressor is suitable for the intended painting or sandblasting tasks.

Proper safety measures, such as wearing protective gear and following established protocols, should always be followed when working with air compressors for painting and sandblasting applications.

air compressor

What is the role of air compressors in manufacturing and industrial processes?

Air compressors play a crucial role in various manufacturing and industrial processes, providing a reliable source of compressed air that powers a wide range of equipment and tools. Here are some key roles of air compressors in manufacturing and industrial settings:

1. Pneumatic Tools and Equipment:

Air compressors power a wide range of pneumatic tools and equipment used in manufacturing processes. These tools include impact wrenches, air drills, sanders, grinders, nail guns, and spray guns. Compressed air provides the necessary force and energy for these tools, enabling efficient and precise operations.

2. Automation and Control Systems:

Compressed air is used in automation and control systems within manufacturing facilities. Pneumatic actuators and valves use compressed air to control the movement of machinery and components. These systems are widely used in assembly lines, packaging operations, and material handling processes.

3. Air Blowing and Cleaning:

Compressed air is employed for blowing and cleaning applications in manufacturing and industrial processes. Air blowguns and air nozzles are used to remove debris, dust, and contaminants from surfaces, machinery, and products. Compressed air is also used for drying, cooling, and purging operations.

4. Air Separation and Gas Generation:

Air compressors are used in air separation plants to generate industrial gases such as nitrogen, oxygen, and argon. These gases are essential for various industrial processes, including metal fabrication, chemical production, and food packaging.

5. HVAC Systems:

Compressed air is utilized in heating, ventilation, and air conditioning (HVAC) systems. It powers pneumatic actuators for damper control, pneumatic controls for pressure regulation, and pneumatic valves for flow control in HVAC applications.

6. Air Compression for Storage and Transport:

Compressed air is used for storage and transport purposes in manufacturing and industrial settings. It is often used to pressurize storage tanks or containers that hold gases or liquids. Compressed air also facilitates the transfer of materials through pipelines and pneumatic conveying systems.

7. Process Instrumentation:

Compressed air is utilized in process instrumentation and control systems. It powers pneumatic instruments such as pressure gauges, flow meters, and control valves. These instruments play a critical role in monitoring and regulating various parameters in industrial processes.

8. Material Handling and Pneumatic Conveying:

In manufacturing and industrial facilities, compressed air is used for material handling and pneumatic conveying systems. It enables the movement of bulk materials such as powders, granules, and pellets through pipelines, facilitating efficient and controlled material transfer.

Overall, air compressors are vital components in manufacturing and industrial processes, providing a versatile and efficient source of power for a wide range of applications. The specific role of air compressors may vary depending on the industry, process requirements, and operational needs.

air compressor

Are there portable air compressors available for home use?

Yes, there are portable air compressors specifically designed for home use. These portable models offer convenience, versatility, and ease of use for various tasks around the house. Here are some key points about portable air compressors for home use:

1. Compact and Lightweight: Portable air compressors are typically compact and lightweight, making them easy to transport and store. They are designed with portability in mind, allowing homeowners to move them around the house or take them to different locations as needed.

2. Electric-Powered: Most portable air compressors for home use are electric-powered. They can be plugged into a standard household electrical outlet, eliminating the need for gasoline or other fuel sources. This makes them suitable for indoor use without concerns about emissions or ventilation.

3. Versatile Applications: Portable air compressors can be used for a wide range of home applications. They are commonly used for inflating tires, sports equipment, and inflatable toys. They are also handy for operating pneumatic tools such as nail guns, staplers, and paint sprayers. Additionally, portable air compressors can be used for cleaning tasks, powering airbrushes, and other light-duty tasks around the house.

4. Pressure and Capacity: Portable air compressors for home use typically have lower pressure and capacity ratings compared to larger industrial or commercial models. They are designed to meet the needs of common household tasks rather than heavy-duty applications. The pressure and capacity of these compressors are usually sufficient for most home users.

5. Oil-Free Operation: Many portable air compressors for home use feature oil-free operation. This means they do not require regular oil changes or maintenance, making them more user-friendly and hassle-free for homeowners.

6. Noise Level: Portable air compressors designed for home use often prioritize low noise levels. They are engineered to operate quietly, reducing noise disturbances in residential environments.

7. Cost: Portable air compressors for home use are generally more affordable compared to larger, industrial-grade compressors. They offer a cost-effective solution for homeowners who require occasional or light-duty compressed air applications.

When considering a portable air compressor for home use, it’s important to assess your specific needs and tasks. Determine the required pressure, capacity, and features that align with your intended applications. Additionally, consider factors such as portability, noise level, and budget to choose a suitable model that meets your requirements.

Overall, portable air compressors provide a practical and accessible compressed air solution for homeowners, allowing them to tackle a variety of tasks efficiently and conveniently within a home setting.

China best New-DC12V Portable-Li-ion Battery Cordless/Electric-Air Pump/Compressor/Tire Inflator Car Automobile Accessories-Power Tools air compressor repair near me
editor by CX 2023-10-09

China wholesaler Fast Delivery Scroll High Pressure Air Compressor 30 Bar One Year Warranty arb air compressor

Product Description

ZheJiang Xihu (West Lake) Dis. specializes in the R&D, manufacturing, sales and after sales service of compressors, which include oil-free air compressors, oil-injected air compressor and air end, special gas compressors and post-processing equipment etc, under the brand name “Xihu (West Lake) Dis.r”, “OFAC”.

OIL FREE SCROLL AIR COMPRESSOR

Model	Motor Power kw/hp	Air Flow L/min	Pressure MPa	Dimension (LWH mm)	Weight kgs
AP1.5-8A	1.5/2	140	0.6-0.8	540540770	87
AP1.5-8B	1.5/2	140		5405401190	136
AP2.2-8A	2.2/3	240		540540770	93
AP2.2-8B	2.2/3	240		5405401190	142
AP3.7-8A	3.7/5	410		540540770	110
AP3.7-8B	3.7/5	410		5405401190	149
AP1.5-10A	1.5/2	120	0.8-1.0	540540770	87
AP1.5-10B	1.5/2	120		5405401190	136
AP2.2-10A	2.2/3	200		540540770	93
AP2.2-10B	2.2/3	200		5405401190	142
AP3.7-10A	3.7/5	340		540540770	110
AP3.7-10B	3.7/5	340		5405401190	149

Model	Motor Power kw/hp	Air Flow L/min	Pressure MPa	Dimension (LWH mm)	Weight kgs
AP7.5-8A	7.5/10	820	0.6-0.8	1000590976	227
AP11-8A	11/15	1230		10505901470	335
AP15-8A	15/20	1640		12507401800	488
AP18.5-8A	18.5/25	2050		12357401990	734
AP7.5-10A	7.5/10	680	0.8-1.0	1000590976	227
AP11-10A	11/15	1571		10505901470	335
AP15-10A	15/20	1360		12507401800	488
AP18.5-10A	18.5/25	1700		12357401990	734

Model	Motor Power kw/hp	Air Flow L/min	Pressure MPa	Dimension (LWH mm)	Weight kgs
AP5.5-C	5.5/7.5	610	0.6-0.8	6607501200	175
AP7.5-8C	7.5/10	800		6607501200	180
AP11-8C	11/15	1220		12507001171	338
AP15-8C	15/20	1640		12507001171	350
AP18.5-8C	18.5/25	2040		12507001602	540
AP22-8C	22/30	2440		12507001602	558
AP30-8C	30/40	3280		123017001602	900
AP33-8C	33/45	3660			1080
AP45-8C	45/60	5000			1116

Model	Motor Power kw/hp	Air Flow L/min	Pressure MPa	Dimension (LWH mm)	Weight kgs
AP22-8A	22/30	2460	0.6-0.8	158012351852	860
AP30-8A	30/40	3280		158012351852	1000
AP37-8A	37/50	4100		158012351990	1470
AP22-8A	22/30	2040	0.8-1.0	158012351630	910
AP30-8A	30/40	2720		158012351990	1140
AP37-8A	37/50	3400		158012351990	1470

TECHNICAL DATA
Model	Power		Pressure (bar)	Air Flow (m3/min)	Noise Level dBA	Outlet Size	Weight (kgs)	Lubricating Water(L)	Filter Element (B)-(Z)	Dimension LxWxH (mm)
OF-7.5F	7.5kw	10hp	8	1.0	60	RP 3/4	400	22	(25cm) 1	10007201050
OF-11F	11kw	15hp	8	1.6	63	RP 3/4	460	22	(25cm) 1	11568451250
OF-15F	15kw	20hp	8	2.5	65	RP 1	620	28	(50cm) 1	13069451260
OF-18F	18.5kw	25hp	8	3.0	67		750	33		152010601390
OF-22F	22kw	30hp	8	3.6	68		840	33		152010601390
OF-30F	30kw	40hp	8	5.0	69	RP 11/4	1050	66	(25cm) 5	176011601490
OF-37F	37kw	50hp	8	6.2	71	RP 11/4	1100	66		176011601490
OF-45S	45kw	60hp	8	7.3	74	RP 11/2	1050	88		176011601490
OF-45F	45kw	60hp	8	7.3	74	RP 11/2	1200	88		176011601490
OF-55S	55kw	75hp	8	10	74	RP 2	1250	110	(50cm) 5	190012501361
OF-55F	55kw	75hp	8	10	74		2200		(50cm) 7	235012501880
OF-75S	75kw	100hp	8	13	75		1650		(50cm) 5	190012501361
OF-75F	75kw	100hp	8	13	75		2500		(50cm) 7	255016201880
OF-90S	90kw	125hp	8	15	76		2050		(50cm) 5	190012501361
OF-90F	90kw	125hp	8	15	76		2650		(50cm) 7	255016201880
OF-110S	110kw	150hp	8	20	78	DN 65	2550	130	(50cm) 12	220016001735
OF-110F	110kw	150hp	8	20	78		3500	130		300017002250
OF-132S	132kw	175hp	8	23	80		2700	130		220016002250
OF-160S	160kw	220hp	8	26	82		2900	165		220016002250
OF-185S	185kw	250hp	8	30	83	DN 100	3300	180	(50cm) 22	286018001945
OF-200S	200kw	270hp	8	33	83		3500			286018001945
OF-220S	220kw	300hp	8	36	85		4500			286020002300
OF-250S	250kw	340hp	8	40	85		4700			286020002300
OF-315S	315kw	480hp	8	50	90		5000			286020002300

F– air cooling method S– water cooling method

  The brand “OFAC, OFC” specializes in the R&D, manufacturing, sales and service of compressors,
  oil-free compressors and air end, special gas compressors, various air compressors and
post-processing equipment, providing customers with High-quality, environmentally friendly and
  efficient air system solutions and fast and stable technical services.

FAQ

Q1: Warranty terms of your machine?
A1: One year warranty for the machine and technical support according to your needs.

Q2: Will you provide some spare parts of the machines?
A2: Yes, of course.

Q3: What about product package?
A3: We pack our products strictly with standard seaworthy case. Rcommend wooden
box.

Q4: Can you use our brand?
A4: Yes, OEM is available.

Q5: How long will you take to arrange production?
A5: Immediate delivery for stock products. 380V 50HZ we can delivery the goods within
3-15 days. Other voltage or other color we will delivery within 30-45 days.

Q6: How Many Staff Are There In your Factory?
A6: About 100.

Q7: What’s your factory’s production capacity?
A7: About 550-650 units per month.

Q8: What the exactly address of your factory?
A8: Our first workshop located in HangZhou, ZheJiang , second workshop located in
HangZhou, ZheJiang , China.

Shipping Cost: Estimated freight per unit.	To be negotiated

After-sales Service:	1 Year
Warranty:	1 Year
Installation Type:	Stationary Type

Customization:	Available \|

air compressor

Can air compressors be used for painting and sandblasting?

Yes, air compressors can be used for both painting and sandblasting applications. Here’s a closer look at how air compressors are utilized for painting and sandblasting:

Painting:

Air compressors are commonly used in painting processes, especially in automotive, industrial, and construction applications. Here’s how they are involved:

Spray Guns: Air compressors power spray guns used for applying paint coatings. The compressed air atomizes the paint, creating a fine mist that can be evenly sprayed onto surfaces. The pressure and volume of the compressed air impact the spray pattern, coverage, and overall finish quality.
Paint Mixers and Agitators: Compressed air is often used to power mixers and agitators that ensure proper blending of paint components. These devices use the compressed air to stir or circulate the paint, preventing settling and maintaining a consistent mixture.
Airbrushing: Air compressors are essential for airbrushing techniques, which require precise control over airflow and pressure. Airbrushes are commonly used in artistic applications, such as illustrations, murals, and fine detailing work.

Sandblasting:

Blasting Cabinets: Air compressors power blasting cabinets or booths, which are enclosed spaces where the sandblasting process takes place. The compressed air propels the abrasive media, such as sand or grit, through a nozzle or gun, creating a forceful stream that impacts the surface being treated.
Abrasive Blasting Pots: Air compressors supply air to abrasive blasting pots or tanks that store and pressurize the abrasive media. The compressed air from the compressor enters the pot, pressurizing it and allowing for a controlled release of the abrasive material during the sandblasting process.
Air Dryers and Filters: In sandblasting applications, it is crucial to have clean, dry air to prevent moisture and contaminants from affecting the abrasive blasting process and the quality of the surface being treated. Air compressors may be equipped with air dryers and filters to remove moisture, oil, and impurities from the compressed air.

Proper safety measures, such as wearing protective gear and following established protocols, should always be followed when working with air compressors for painting and sandblasting applications.

air compressor

Can air compressors be used for inflating tires and sporting equipment?

Yes, air compressors can be used for inflating tires and sporting equipment, providing a convenient and efficient method for achieving the desired air pressure. Here’s how air compressors are used for these purposes:

1. Tire Inflation:

Air compressors are commonly used for inflating vehicle tires, including car tires, motorcycle tires, bicycle tires, and even larger truck or trailer tires. Air compressors provide a continuous source of pressurized air, allowing for quick and accurate inflation. They are often used in automotive repair shops, gas stations, and by individuals who regularly need to inflate tires.

2. Sporting Equipment Inflation:

Air compressors are also useful for inflating various types of sporting equipment. This includes inflatable balls such as soccer balls, basketballs, footballs, and volleyballs. Additionally, air compressors can be used to inflate inflatable water toys, air mattresses, inflatable kayaks, and other recreational items that require air for proper inflation.

3. Air Tools for Inflation:

Air compressors can power air tools specifically designed for inflation purposes. These tools, known as inflators or air blow guns, provide controlled airflow for inflating tires and sporting equipment. They often have built-in pressure gauges and nozzles designed to fit different types of valves, making them versatile and suitable for various inflation tasks.

4. Adjustable Pressure:

One advantage of using air compressors for inflation is the ability to adjust the pressure. Most air compressors allow users to set the desired pressure level using a pressure regulator or control knob. This feature ensures that tires and sporting equipment are inflated to the recommended pressure, promoting optimal performance and safety.

5. Efficiency and Speed:

Air compressors provide a faster and more efficient inflation method compared to manual pumps. The continuous supply of compressed air allows for quick inflation, reducing the time and effort required to inflate tires and sporting equipment manually.

6. Portable Air Compressors:

For inflating tires and sporting equipment on the go, portable air compressors are available. These compact and lightweight compressors can be easily carried in vehicles or taken to sports events and outdoor activities, ensuring convenient access to a reliable air supply.

It is important to note that when using air compressors for inflating tires, it is recommended to follow manufacturer guidelines and proper inflation techniques to ensure safety and avoid overinflation.

air compressor

What is the difference between a piston and rotary screw compressor?

Piston compressors and rotary screw compressors are two common types of air compressors with distinct differences in their design and operation. Here’s a detailed explanation of the differences between these two compressor types:

1. Operating Principle:

Piston Compressors: Piston compressors, also known as reciprocating compressors, use one or more pistons driven by a crankshaft to compress air. The piston moves up and down within a cylinder, creating a vacuum during the intake stroke and compressing the air during the compression stroke.
Rotary Screw Compressors: Rotary screw compressors utilize two intermeshing screws (rotors) to compress air. As the male and female screws rotate, the air is trapped between them and gradually compressed as it moves along the screw threads.

2. Compression Method:

Piston Compressors: Piston compressors achieve compression through a positive displacement process. The air is drawn into the cylinder and compressed as the piston moves back and forth. The compression is intermittent, occurring in discrete cycles.
Rotary Screw Compressors: Rotary screw compressors also employ a positive displacement method. The compression is continuous as the rotating screws create a continuous flow of air and compress it gradually as it moves along the screw threads.

3. Efficiency:

Piston Compressors: Piston compressors are known for their high efficiency at lower flow rates and higher pressures. They are well-suited for applications that require intermittent or variable air demand.
Rotary Screw Compressors: Rotary screw compressors are highly efficient for continuous operation and are designed to handle higher flow rates. They are often used in applications with a constant or steady air demand.

4. Noise Level:

Piston Compressors: Piston compressors tend to generate more noise during operation due to the reciprocating motion of the pistons and valves.
Rotary Screw Compressors: Rotary screw compressors are generally quieter in operation compared to piston compressors. The smooth rotation of the screws contributes to reduced noise levels.

5. Maintenance:

Piston Compressors: Piston compressors typically require more frequent maintenance due to the higher number of moving parts, such as pistons, valves, and rings.
Rotary Screw Compressors: Rotary screw compressors have fewer moving parts, resulting in lower maintenance requirements. They often have longer service intervals and can operate continuously for extended periods without significant maintenance.

6. Size and Portability:

Piston Compressors: Piston compressors are available in both smaller portable models and larger stationary units. Portable piston compressors are commonly used in construction, automotive, and DIY applications.
Rotary Screw Compressors: Rotary screw compressors are typically larger and more suitable for stationary installations in industrial and commercial settings. They are less commonly used in portable applications.

These are some of the key differences between piston compressors and rotary screw compressors. The choice between the two depends on factors such as required flow rate, pressure, duty cycle, efficiency, noise level, maintenance needs, and specific application requirements.

China wholesaler Fast Delivery Scroll High Pressure Air Compressor 30 Bar One Year Warranty arb air compressor
editor by CX 2023-10-08

China Custom R-134A 96394698 AC Air Compressor for Sale lowes air compressor

Product Description

We are China Top 1 Brand source factory accessories supplier, high quality, high matching degree,
more professional and more favorable price.

Part Name	AC Air Compressor
Part No.	R134a, etc. All model
Warranty	3 Months
Payment	TT/Paypal/Western Union
Delivery time	1-5 days
MOQ	1 Pc
Condition	100% New

1. WHO ARE WE?
HangZhou XIHU (WEST LAKE) DIS.NG ENGINEERING MACHINERY CO.,LTD is a leading construction machinery exporter,located in
HangZhou city,ZheJiang province where HangZhou Construction Machinery Group Inc in. We have the domestic agency rights
of them more than 10years,based on the advantage of them,we also estabish long-time business with other famous
brands.

2. HOW IS YOUR PRICE COMPARED WITH MANUFACTURERS/FACTORIES?
We work as the leading dealers of various leading China construction machinery manufacturers/ factories, and are
constantly treated with best dealership price. From numerous comparison and feedbacks from clients, our price is more
competitive than the price from manufacturers/factories.

3. HOW IS YOUR DELIVERY TIME?
In general circumstance, we can have an immediate delivery of regular machines for our clients within 7 days, because
we have a variety of resources to check machines in stock, locally and nation widely, and to receive machines in timely
manner. But for manufacturers/factories, it will take more than 30 days to produce the ordered machine.

4. HOW SOON CAN YOU RESPOND CLIENT INQUIRIES?
Our team is consisted of a group of diligent and dynamic people, working 247 to respond client inquiries and questions
all the time Most problems can be solved within 4 hours while manufacturers/factories will take much longer to give
response.

5. WHICH PAYMENT TERMS CAN YOU ACCEPT?
Normally we can work on T/T term or L/ term, sometime DP term.
1)On T/T term, 30% down payment is required in advance, and 70% balance shall be settled before shipment, or
against the copy of original B/L for long-term cooperating client.
2)On L/C term, a 100% irrevocable L/ C without “soft clauses”from an international recognized bank can be accepted.
Please seek the advice from the individual sales manager whom you work with.

6. WHAT SERVICES CAN WE PROVIDE?
Accepted Delivery Terms: FOB,CFR,CIF;
Accepted Payment Currency:USD,EUR;
Accepted Payment Type: T/T,L/C,Western Union,Cash;
Language Spoken:English,Chinese

7. WHAT PRODUCTS YOU CAN GET FROM US?
Our main products including,wheel loader,backhoe loader,truck crane,crawler crane,tower crane,road roller,motor
grader,excavator,bulldozer,forklift,dump truck,trailer,tractor truck,special vehicle ,Marine Machinery and all of their
spare parts.

Shipping Cost: Estimated freight per unit.	To be negotiated

After-sales Service:	Global Warranty
Warranty:	1 Year
Certification:	CE

Samples:	US$ 129/Piece 1 Piece(Min.Order) \| Order Sample

Customization:	Available \|

air compressor

What are the differences between stationary and portable air compressors?

Stationary and portable air compressors are two common types of air compressors with distinct features and applications. Here are the key differences between them:

1. Mobility:

The primary difference between stationary and portable air compressors is their mobility. Stationary air compressors are designed to be permanently installed in a fixed location, such as a workshop or a factory. They are typically larger, heavier, and not easily movable. On the other hand, portable air compressors are smaller, lighter, and equipped with handles or wheels for easy transportation. They can be moved from one location to another, making them suitable for jobsites, construction sites, and other mobile applications.

2. Power Source:

Another difference lies in the power source used by stationary and portable air compressors. Stationary compressors are usually powered by electricity, as they are designed for continuous operation in a fixed location with access to power outlets. They are connected to the electrical grid or have dedicated wiring. In contrast, portable compressors are available in various power options, including electric, gasoline, and diesel engines. This versatility allows them to operate in remote areas or sites without readily available electricity.

3. Tank Capacity:

Tank capacity is also a distinguishing factor between stationary and portable air compressors. Stationary compressors often have larger storage tanks to store compressed air for extended periods. The larger tanks enable them to deliver a continuous and steady supply of compressed air for longer durations without the need for frequent cycling. Portable compressors, due to their compact size and portability, generally have smaller tank capacities, which may be sufficient for intermittent or smaller-scale applications.

4. Performance and Output:

The performance and output capabilities of stationary and portable air compressors can vary. Stationary compressors are typically designed for high-volume applications that require a consistent and continuous supply of compressed air. They often have higher horsepower ratings, larger motor sizes, and higher air delivery capacities. Portable compressors, while generally offering lower horsepower and air delivery compared to their stationary counterparts, are still capable of delivering sufficient air for a range of applications, including pneumatic tools, inflation tasks, and light-duty air-powered equipment.

5. Noise Level:

Noise level is an important consideration when comparing stationary and portable air compressors. Stationary compressors, being larger and built for industrial or commercial settings, are often equipped with noise-reducing features such as sound insulation and vibration dampening. They are designed to operate at lower noise levels, which is crucial for maintaining a comfortable working environment. Portable compressors, while efforts are made to reduce noise, may produce higher noise levels due to their compact size and portability.

6. Price and Cost:

Stationary and portable air compressors also differ in terms of price and cost. Stationary compressors are generally more expensive due to their larger size, higher power output, and industrial-grade construction. They often require professional installation and may involve additional costs such as electrical wiring and system setup. Portable compressors, being smaller and more versatile, tend to have a lower upfront cost. They are suitable for individual users, contractors, and small businesses with budget constraints or flexible air supply needs.

When selecting between stationary and portable air compressors, it is essential to consider the specific requirements of the intended application, such as mobility, power source availability, air demands, and noise considerations. Understanding these differences will help in choosing the appropriate type of air compressor for the intended use.

air compressor

How do you choose the right air compressor for woodworking?

Choosing the right air compressor for woodworking is essential to ensure efficient and effective operation of pneumatic tools and equipment. Here are some factors to consider when selecting an air compressor for woodworking:

1. Required Air Volume (CFM):

Determine the required air volume or cubic feet per minute (CFM) for your woodworking tools and equipment. Different tools have varying CFM requirements, so it is crucial to choose an air compressor that can deliver the required CFM to power your tools effectively. Make sure to consider the highest CFM requirement among the tools you’ll be using simultaneously.

2. Tank Size:

Consider the tank size of the air compressor. A larger tank allows for more stored air, which can be beneficial when using tools that require short bursts of high air volume. It helps maintain a consistent air supply and reduces the frequency of the compressor cycling on and off. However, if you have tools with continuous high CFM demands, a larger tank may not be as critical.

3. Maximum Pressure (PSI):

Check the maximum pressure (PSI) rating of the air compressor. Woodworking tools typically operate within a specific PSI range, so ensure that the compressor can provide the required pressure. It is advisable to choose an air compressor with a higher maximum PSI rating to accommodate any future tool upgrades or changes in your woodworking needs.

4. Noise Level:

Consider the noise level of the air compressor, especially if you’ll be using it in a residential or shared workspace. Some air compressors have noise-reducing features or are designed to operate quietly, making them more suitable for woodworking environments where noise control is important.

5. Portability:

Assess the portability requirements of your woodworking projects. If you need to move the air compressor frequently or work in different locations, a portable and lightweight compressor may be preferable. However, if the compressor will remain stationary in a workshop, a larger, stationary model might be more suitable.

6. Power Source:

Determine the power source available in your woodworking workspace. Air compressors can be powered by electricity or gasoline engines. If electricity is readily available, an electric compressor may be more convenient and cost-effective. Gasoline-powered compressors offer greater flexibility for remote or outdoor woodworking projects where electricity may not be accessible.

7. Quality and Reliability:

Choose an air compressor from a reputable manufacturer known for producing reliable and high-quality equipment. Read customer reviews and consider the warranty and after-sales support offered by the manufacturer to ensure long-term satisfaction and reliability.

8. Budget:

Consider your budget and balance it with the features and specifications required for your woodworking needs. While it’s important to invest in a reliable and suitable air compressor, there are options available at various price points to accommodate different budgets.

By considering these factors and evaluating your specific woodworking requirements, you can choose an air compressor that meets the demands of your tools, provides efficient performance, and enhances your woodworking experience.

air compressor

How is air pressure measured in air compressors?

Air pressure in air compressors is typically measured using one of two common units: pounds per square inch (PSI) or bar. Here’s a brief explanation of how air pressure is measured in air compressors:

1. Pounds per Square Inch (PSI): PSI is the most widely used unit of pressure measurement in air compressors, especially in North America. It represents the force exerted by one pound of force over an area of one square inch. Air pressure gauges on air compressors often display pressure readings in PSI, allowing users to monitor and adjust the pressure accordingly.

2. Bar: Bar is another unit of pressure commonly used in air compressors, particularly in Europe and many other parts of the world. It is a metric unit of pressure equal to 100,000 pascals (Pa). Air compressors may have pressure gauges that display readings in bar, providing an alternative measurement option for users in those regions.

To measure air pressure in an air compressor, a pressure gauge is typically installed on the compressor’s outlet or receiver tank. The gauge is designed to measure the force exerted by the compressed air and display the reading in the specified unit, such as PSI or bar.

It’s important to note that the air pressure indicated on the gauge represents the pressure at a specific point in the air compressor system, typically at the outlet or tank. The actual pressure experienced at the point of use may vary due to factors such as pressure drop in the air lines or restrictions caused by fittings and tools.

When using an air compressor, it is essential to set the pressure to the appropriate level required for the specific application. Different tools and equipment have different pressure requirements, and exceeding the recommended pressure can lead to damage or unsafe operation. Most air compressors allow users to adjust the pressure output using a pressure regulator or similar control mechanism.

Regular monitoring of the air pressure in an air compressor is crucial to ensure optimal performance, efficiency, and safe operation. By understanding the units of measurement and using pressure gauges appropriately, users can maintain the desired air pressure levels in their air compressor systems.

China Custom R-134A 96394698 AC Air Compressor for Sale lowes air compressor
editor by CX 2023-10-08

China Best Sales 15nm3/H High Pressure Oil-Free Air Compressor Propylene Silicon Trichloride LPG Diaphragm Compressor best air compressor

Product Description

HangZhou CHINAMFG Gas Equipment Co.,Ltd, exporting diaphragm compressor, piston compressor, oxygen generator, gas cylinder and nitrogen generators with good quality and low price.

Diaphragm compressor is a reciprocating compressor that compresses and transports gas by the reciprocating motion of the diaphragm in the cylinder. The diaphragm is clamped by 2 restraint plates along the periphery and forms a cylinder. The diaphragm is driven by hydraulic force to move back and forth in the cylinder, so as to achieve the compression and transportation of gas. With a large compression ratio, wide pressure range, good sealing characteristics. Since its gas chamber does not need any lubrication, thus ensuring the purity of compressed gas, especially suitable for flammable, explosive, toxic and harmful, high-purity gas compression, transportation and bottling.

After-sales Service:	18 Months
Warranty:	18 Months
Principle:	Displacement Compressor
Application:	High Back Pressure Type
Performance:	Low Noise, Variable Frequency, Explosion-Proof
Mute:	Low Noise

Customization:	Available \|

air compressor

What are the energy-saving technologies available for air compressors?

There are several energy-saving technologies available for air compressors that help improve their efficiency and reduce energy consumption. These technologies aim to optimize the operation of air compressors and minimize energy losses. Here are some common energy-saving technologies used:

1. Variable Speed Drive (VSD) Compressors:

VSD compressors are designed to adjust the motor speed according to the compressed air demand. By varying the motor speed, these compressors can match the output to the actual air requirement, resulting in energy savings. VSD compressors are particularly effective in applications with varying air demands, as they can operate at lower speeds during periods of lower demand, reducing energy consumption.

2. Energy-Efficient Motors:

The use of energy-efficient motors in air compressors can contribute to energy savings. High-efficiency motors, such as those with premium efficiency ratings, are designed to minimize energy losses and operate more efficiently than standard motors. By using energy-efficient motors, air compressors can reduce energy consumption and achieve higher overall system efficiency.

3. Heat Recovery Systems:

Air compressors generate a significant amount of heat during operation. Heat recovery systems capture and utilize this wasted heat for other purposes, such as space heating, water heating, or preheating process air or water. By recovering and utilizing the heat, air compressors can provide additional energy savings and improve overall system efficiency.

4. Air Receiver Tanks:

Air receiver tanks are used to store compressed air and provide a buffer during periods of fluctuating demand. By using appropriately sized air receiver tanks, the compressed air system can operate more efficiently. The tanks help reduce the number of starts and stops of the air compressor, allowing it to run at full load for longer periods, which is more energy-efficient than frequent cycling.

5. System Control and Automation:

Implementing advanced control and automation systems can optimize the operation of air compressors. These systems monitor and adjust the compressed air system based on demand, ensuring that only the required amount of air is produced. By maintaining optimal system pressure, minimizing leaks, and reducing unnecessary air production, control and automation systems help achieve energy savings.

6. Leak Detection and Repair:

Air leaks in compressed air systems can lead to significant energy losses. Regular leak detection and repair programs help identify and fix air leaks promptly. By minimizing air leakage, the demand on the air compressor is reduced, resulting in energy savings. Utilizing ultrasonic leak detection devices can help locate and repair leaks more efficiently.

7. System Optimization and Maintenance:

Proper system optimization and routine maintenance are essential for energy savings in air compressors. This includes regular cleaning and replacement of air filters, optimizing air pressure settings, ensuring proper lubrication, and conducting preventive maintenance to keep the system running at peak efficiency.

By implementing these energy-saving technologies and practices, air compressor systems can achieve significant energy efficiency improvements, reduce operational costs, and minimize environmental impact.

air compressor

What is the role of air compressors in manufacturing and industrial processes?

1. Pneumatic Tools and Equipment:

2. Automation and Control Systems:

3. Air Blowing and Cleaning:

4. Air Separation and Gas Generation:

5. HVAC Systems:

6. Air Compression for Storage and Transport:

7. Process Instrumentation:

8. Material Handling and Pneumatic Conveying:

air compressor

Can air compressors be used for automotive applications?

China Best Sales 15nm3/H High Pressure Oil-Free Air Compressor Propylene Silicon Trichloride LPG Diaphragm Compressor best air compressor
editor by CX 2023-10-07

China high quality 48V 60V 72V Cooler Cooling System Electric 12V 24V Parking Conditioner Auto Parts Air Compressor air compressor portable

Product Description

Name	Electric compressor
Type	Scroll
Freon	R134a
Displacement	18~27cc
refrigerant oil	POE68 130ml
Weight	5.6kg
Power	12V:550W; 24V:850W
RPM	12V:1800rpm; 24V: 3000rpm

We have many types of air conditioners for your option, including rooftop type, split type, invisible type and so on.

Company Profile

Quality, responsibility and innovation, have always been what CHINAMFG Environment Technology Co., Ltd. Pursues.

With standard workshops over 35, 000 square meters, our factory covers an area of 80 acres, with 235 employees and 23 engineers. Concentrating on air solutions, we manufacture parking air conditioners, parking heaters, scroll and rotary compressors, DC generators and so on.

To ensure quality, we are equipped with a complete set of advanced equipment, including CNC machining, turning and milling compound machining, Mitutoyo three-coordinate measuring instrument, Flip-type impregnation equipment, automatic ultrasonic cleaning machine. Meanwhile advanced automotive electric air conditioning system environment simulation laboratories have been established. All products will go through 100% test according to ISO9001 and CE standards before launching market.

Our research and development team provides customization and after-sales support. New products will be launched every couple of months, showing the best appearance and most reliable function, leading the trend of the industry.

After-sales Service:	Tech Support
Warranty:	1 Year
Classification:	Variable Capacity
Job Classification:	Reciprocating
Transmission Power:	Turbine
Cooling Method:	Air-cooled

Samples:	US$ 150/Piece 1 Piece(Min.Order) \| Request Sample

Customization:	Available \|

air compressor

What are the advantages of using an air compressor in construction?

Powering Pneumatic Tools: Air compressors are commonly used to power a wide range of pneumatic tools on construction sites. Tools such as jackhammers, nail guns, impact wrenches, drills, and sanders can be operated using compressed air. Pneumatic tools are often preferred due to their lightweight, compact design and ability to deliver high torque or impact force.
Efficient Operation: Air compressors provide a continuous and reliable source of power for pneumatic tools, allowing for uninterrupted operation without the need for frequent battery changes or recharging. This helps to maintain a smooth workflow and reduces downtime.
Portability: Many construction air compressors are designed to be portable, featuring wheels or handles for easy maneuverability on job sites. Portable air compressors can be transported to different areas of the construction site as needed, providing power wherever it is required.
Versatility: Air compressors are versatile tools that can be used for various applications in construction. Apart from powering pneumatic tools, they can also be utilized for tasks such as inflating tires, cleaning debris, operating air-operated pumps, and powering air horns.
Increased Productivity: The efficient operation and power output of air compressors enable construction workers to complete tasks more quickly and effectively. Pneumatic tools powered by air compressors often offer higher performance and faster operation compared to their electric or manual counterparts.
Cost Savings: Air compressors can contribute to cost savings in construction projects. Pneumatic tools powered by air compressors are generally more durable and have longer lifespans compared to electric tools. Additionally, since air compressors use compressed air as their power source, they do not require the purchase or disposal of batteries or fuel, reducing ongoing operational expenses.
Reduced Electrocution Risk: Construction sites can be hazardous environments, with the risk of electrocution from electrical tools or equipment. By utilizing air compressors and pneumatic tools, the reliance on electrical power is minimized, reducing the risk of electrocution accidents.

air compressor

How do you maintain proper air quality in compressed air systems?

Maintaining proper air quality in compressed air systems is essential to ensure the reliability and performance of pneumatic equipment and the safety of downstream processes. Here are some key steps to maintain air quality:

1. Air Filtration:

Install appropriate air filters in the compressed air system to remove contaminants such as dust, dirt, oil, and water. Filters are typically placed at various points in the system, including the compressor intake, aftercoolers, and before point-of-use applications. Regularly inspect and replace filters to ensure their effectiveness.

2. Moisture Control:

Excessive moisture in compressed air can cause corrosion, equipment malfunction, and compromised product quality. Use moisture separators or dryers to remove moisture from the compressed air. Refrigerated dryers, desiccant dryers, or membrane dryers are commonly employed to achieve the desired level of dryness.

3. Oil Removal:

If the compressed air system utilizes oil-lubricated compressors, it is essential to incorporate proper oil removal mechanisms. This can include coalescing filters or adsorption filters to remove oil aerosols and vapors from the air. Oil-free compressors eliminate the need for oil removal.

4. Regular Maintenance:

Perform routine maintenance on the compressed air system, including inspections, cleaning, and servicing of equipment. This helps identify and address any potential issues that may affect air quality, such as leaks, clogged filters, or malfunctioning dryers.

5. Air Receiver Tank Maintenance:

Regularly drain and clean the air receiver tank to remove accumulated contaminants, including water and debris. Proper maintenance of the tank helps prevent contamination from being introduced into the compressed air system.

6. Air Quality Testing:

Periodically test the quality of the compressed air using appropriate instruments and methods. This can include measuring particle concentration, oil content, dew point, and microbial contamination. Air quality testing provides valuable information about the effectiveness of the filtration and drying processes and helps ensure compliance with industry standards.

7. Education and Training:

Educate personnel working with compressed air systems about the importance of air quality and the proper procedures for maintaining it. Provide training on the use and maintenance of filtration and drying equipment, as well as awareness of potential contaminants and their impact on downstream processes.

8. Documentation and Record-Keeping:

Maintain accurate records of maintenance activities, including filter replacements, drying system performance, and air quality test results. Documentation helps track the system’s performance over time and provides a reference for troubleshooting or compliance purposes.

By implementing these practices, compressed air systems can maintain proper air quality, minimize equipment damage, and ensure the integrity of processes that rely on compressed air.

air compressor

What is the impact of tank size on air compressor performance?

The tank size of an air compressor plays a significant role in its performance and functionality. Here are the key impacts of tank size:

1. Air Storage Capacity: The primary function of the air compressor tank is to store compressed air. A larger tank size allows for greater air storage capacity. This means the compressor can build up a reserve of compressed air, which can be useful for applications that require intermittent or fluctuating air demand. Having a larger tank ensures a steady supply of compressed air during peak usage periods.

2. Run Time: The tank size affects the run time of the air compressor. A larger tank can provide longer continuous operation before the compressor motor needs to restart. This is because the compressed air in the tank can be used to meet the demand without the need for the compressor to run continuously. It reduces the frequency of motor cycling, which can improve energy efficiency and prolong the motor’s lifespan.

3. Pressure Stability: A larger tank helps maintain stable pressure during usage. When the compressor is running, it fills the tank until it reaches a specified pressure level, known as the cut-out pressure. As the air is consumed from the tank, the pressure drops to a certain level, known as the cut-in pressure, at which point the compressor restarts to refill the tank. A larger tank size results in a slower pressure drop during usage, ensuring more consistent and stable pressure for the connected tools or equipment.

4. Duty Cycle: The duty cycle refers to the amount of time an air compressor can operate within a given time period. A larger tank size can increase the duty cycle of the compressor. The compressor can run for longer periods before reaching its duty cycle limit, reducing the risk of overheating and improving overall performance.

5. Tool Compatibility: The tank size can also impact the compatibility with certain tools or equipment. Some tools, such as high-demand pneumatic tools or spray guns, require a continuous and adequate supply of compressed air. A larger tank size ensures that the compressor can meet the air demands of such tools without causing pressure drops or affecting performance.

It is important to note that while a larger tank size offers advantages in terms of air storage and performance, it also results in a larger and heavier compressor unit. Consider the intended application, available space, and portability requirements when selecting an air compressor with the appropriate tank size.

Ultimately, the optimal tank size for an air compressor depends on the specific needs of the user and the intended application. Assess the air requirements, duty cycle, and desired performance to determine the most suitable tank size for your air compressor.

China high quality 48V 60V 72V Cooler Cooling System Electric 12V 24V Parking Conditioner Auto Parts Air Compressor air compressor portable
editor by CX 2023-10-07

China Hot selling 18bar 18m3 650cfm 196kw 200kw Diesel Screw Air Compressor for Water Well Drilling Rig wholesaler

Product Description

Product Description

Model			MDS650S-18
Compressor	Air Delivery	m3/min	18
		cu.ft/min	650
	Discharged Pressure	bar	18
		psig	261
	Capacity of pressure Reserrvoir (L)		168
Engine	Manufacture & Model		Cummins-6CTA8.3-C260
	Cylinder Number		6
	Displacement (L)		8.3
	Rotating Speed	Rated (r/min)	2000
		Idle (r/min)	1400
	Rated Power(KW[HP])		196
	Fuel Capacity(L)		550
	Voltage of Battery		24
	Pipe Size×No		3/4″ 1pcs ,1/2″ 1pcs
Size	Dimension	L(mm)	4210
		W(mm)	2000
		H (mm)	2220
	Weight (Kg)		4400

Our products

Company Information

After-sales Service:	Online
Warranty:	2 Years
Lubrication Style:	Lubricated
Cooling System:	Water Cooling
Power Source:	Diesel Engine
Cylinder Position:	Vertical

Customization:	Available \|

air compressor

Can air compressors be used for shipbuilding and maritime applications?

Air compressors are widely used in shipbuilding and maritime applications for a variety of tasks and operations. The maritime industry relies on compressed air for numerous essential functions. Here’s an overview of how air compressors are employed in shipbuilding and maritime applications:

1. Pneumatic Tools and Equipment:

Air compressors are extensively used to power pneumatic tools and equipment in shipbuilding and maritime operations. Pneumatic tools such as impact wrenches, drills, grinders, sanders, and chipping hammers require compressed air to function. The versatility and power provided by compressed air make it an ideal energy source for heavy-duty tasks, maintenance, and construction activities in shipyards and onboard vessels.

2. Painting and Surface Preparation:

Air compressors play a crucial role in painting and surface preparation during shipbuilding and maintenance. Compressed air is used to power air spray guns, sandblasting equipment, and other surface preparation tools. Compressed air provides the force necessary for efficient and uniform application of paints, coatings, and protective finishes, ensuring the durability and aesthetics of ship surfaces.

3. Pneumatic Actuation and Controls:

Air compressors are employed in pneumatic actuation and control systems onboard ships. Compressed air is used to operate pneumatic valves, actuators, and control devices that regulate the flow of fluids, control propulsion systems, and manage various shipboard processes. Pneumatic control systems offer reliability and safety advantages in maritime applications.

4. Air Start Systems:

In large marine engines, air compressors are used in air start systems. Compressed air is utilized to initiate the combustion process in the engine cylinders. The compressed air is injected into the cylinders to turn the engine’s crankshaft, enabling the ignition of fuel and starting the engine. Air start systems are commonly found in ship propulsion systems and power generation plants onboard vessels.

5. Pneumatic Conveying and Material Handling:

In shipbuilding and maritime operations, compressed air is used for pneumatic conveying and material handling. Compressed air is utilized to transport bulk materials, such as cement, sand, and grain, through pipelines or hoses. Pneumatic conveying systems enable efficient and controlled transfer of materials, facilitating construction, cargo loading, and unloading processes.

6. Air Conditioning and Ventilation:

Air compressors are involved in air conditioning and ventilation systems onboard ships. Compressed air powers air conditioning units, ventilation fans, and blowers, ensuring proper air circulation, cooling, and temperature control in various ship compartments, cabins, and machinery spaces. Compressed air-driven systems contribute to the comfort, safety, and operational efficiency of maritime environments.

These are just a few examples of how air compressors are utilized in shipbuilding and maritime applications. Compressed air’s versatility, reliability, and convenience make it an indispensable energy source for various tasks and systems in the maritime industry.

air compressor

What safety precautions should be taken when working with compressed air?

1. Personal Protective Equipment (PPE):

2. Compressed Air Storage:

3. Pressure Regulation:

4. Air Hose Inspection:

Regularly inspect air hoses for signs of damage, such as cuts, abrasions, or leaks. Replace damaged hoses immediately to prevent potential accidents or loss of pressure.

5. Air Blowguns:

6. Air Tool Safety:

7. Air Compressor Maintenance:

8. Training and Education:

9. Lockout/Tagout:

10. Proper Ventilation:

By adhering to these safety precautions, individuals can minimize the risks associated with working with compressed air and create a safer work environment.

air compressor

Are there portable air compressors available for home use?

6. Noise Level: Portable air compressors designed for home use often prioritize low noise levels. They are engineered to operate quietly, reducing noise disturbances in residential environments.

China Hot selling 18bar 18m3 650cfm 196kw 200kw Diesel Screw Air Compressor for Water Well Drilling Rig wholesaler
editor by CX 2023-10-06

China factory CHINAMFG GA Series Screw Air Compressor GA75VSD air compressor lowes

Product Description

Atlas Copco GA series Screw Air Compressor
Model: GA75VSD

Total capability, total responsibility
Right at the heart of your business, CHINAMFG delivers quality compressed air for superior operational capacity. From compressed air generation to point of use, you can choose from
Our wide range of products to create a complete compressed air system tailored to your specific
Needs. All CHINAMFG products are engineered to integrate seamlessly, ensuring the highest level
Of reliability and energy efficiency. As a result, CHINAMFG can take full responsibility for your
Compressed air infrastructure with a guarantee of best-in-class quality. With a global presence in
Over 150 countries, we can provide an unrivalled service to maintain and continually improve your
Compressed air system performance. Backed by 100 years at the forefront of compressed air, CHINAMFG products offer the finest quality and efficiency. Our goal is to be First in Mind- First in Choice. That is why Atlas Copco’s pursuit of innovation never ceases, driven by the dedication to meet and exceed your demands. Always working with you, we are committed to providing the customized air solution that is the driving force behind your business.

The screw air compressor main configures as follows:
1. Main frame: Sweden Atlas
2. Bearing: 100% Sweden CHINAMFG (LIFE60000hours)
3. Solenoid valve: CEME Italy
4. Electro motor: ABB XIHU (WEST LAKE) DIS.
5. Thermostat valve: Austria Hoerbiger
6. Pressure sensor: Switzerland Huba imported with original
7. Container: ZheJiang shenjiang
8. Oil filter: Germany MANN Company imported with original
9. Oil and gas separator: Germany MANN Company imported with original
10. Lubricating Oil: Sweden Atlas screw air compressor oil imported with original
11. Suction valve: Sweden Atlas imported with original
12. Pressure valve: Hoerbiger Austria Company
13. PLC: Schneider Electric France
14. Oil system configuration of the pipeline were chrome-plated brass
More than 80% of imported famous brand accessories!

Bestrand is a leading supplier of compressed air system. Past 10 years, we established very good partnership with Atlas Copco. We have provided all kinds of products from CHINAMFG include air compressor, after treatment, spare parts to customers all over the world. Pls feel free to contact us for a quote.

Our company’s purpose – to help make life better by relying on us – and the set of values that define us are the foundation of our company’s culture and success. We think and act like owners, taking responsibility for our own actions and always striving to care for our neighbors and create a brighter, healthier shared planet for everyone. We are committed to the success of our customers. Our goal is to operate with clarity and straightforwardness, building lifelong, ongoing and meaningful connections with our customers.

We are driven by a spirit of action and an entrepreneurial spirit of innovation and progress; we accept and embrace the many challenges that come with such responsibility. We speak honestly, admit mistakes, and always strive for openness and clarity. We have bold ambitions while moving CHINAMFG with humility and integrity, striving to earn trust every day. We have the expertise and experience to solve the toughest problems, but no matter how difficult the challenge, we are always sincere and humble. We are committed to fostering team innovation and cultivating and celebrating a culture that embraces diverse opinions, backgrounds and experiences. Employees who are driven by our purpose and values are an unstoppable force that strengthens our ability to deliver benefits to our stakeholders and ensure the long-term health and safety of our company.

Lubrication Style:	Lubricated
Cooling System:	Air Cooling or Water Cooling
Power Source:	AC Power
Cylinder Position:	Vertical
Structure Type:	Closed Type
Installation Type:	Stationary Type

Customization:	Available \|

air compressor

How are air compressors utilized in pharmaceutical manufacturing?

Air compressors play a crucial role in pharmaceutical manufacturing, where they are utilized for various critical applications. The pharmaceutical industry requires a reliable source of clean and compressed air to ensure the safety, efficiency, and quality of its processes. Here’s an overview of how air compressors are utilized in pharmaceutical manufacturing:

1. Manufacturing Processes:

Air compressors are used in numerous manufacturing processes within the pharmaceutical industry. Compressed air is employed for tasks such as mixing and blending of ingredients, granulation, tablet compression, coating, and encapsulation of pharmaceutical products. The controlled delivery of compressed air facilitates precise and consistent manufacturing processes, ensuring the production of high-quality pharmaceuticals.

2. Instrumentation and Control Systems:

Pharmaceutical manufacturing facilities rely on compressed air for powering instrumentation and control systems. Compressed air is used to operate pneumatic valves, actuators, and control devices that regulate the flow of fluids, control temperature and pressure, and automate various processes. The clean and dry nature of compressed air makes it ideal for maintaining the integrity and accuracy of these critical control mechanisms.

3. Packaging and Filling:

Air compressors are employed in pharmaceutical packaging and filling processes. Compressed air is used to power machinery and equipment for bottle cleaning, labeling, capping, and sealing of pharmaceutical products. Compressed air provides the necessary force and precision for efficient and reliable packaging, ensuring product safety and compliance.

4. Cleanroom Environments:

Pharmaceutical manufacturing often takes place in controlled cleanroom environments to prevent contamination and maintain product quality. Air compressors are used to supply clean and filtered compressed air to these cleanrooms, ensuring a controlled and sterile environment for the production of pharmaceuticals. Compressed air is also utilized in cleanroom air showers and air curtains for personnel and material decontamination.

5. Laboratory Applications:

In pharmaceutical laboratories, air compressors are utilized for various applications. Compressed air is used in laboratory instruments, such as gas chromatographs, mass spectrometers, and other analytical equipment. It is also employed in clean air cabinets, fume hoods, and laminar flow benches, providing a controlled and clean environment for testing, analysis, and research.

6. HVAC Systems:

Air compressors are involved in heating, ventilation, and air conditioning (HVAC) systems in pharmaceutical manufacturing facilities. Compressed air powers the operation of HVAC controls, dampers, actuators, and air handling units, ensuring proper air circulation, temperature control, and environmental conditions in various manufacturing areas.

By utilizing air compressors in pharmaceutical manufacturing, the industry can maintain strict quality standards, enhance operational efficiency, and ensure the safety and efficacy of pharmaceutical products.

air compressor

Can air compressors be used for inflating tires and sporting equipment?

1. Tire Inflation:

2. Sporting Equipment Inflation:

3. Air Tools for Inflation:

4. Adjustable Pressure:

5. Efficiency and Speed:

6. Portable Air Compressors:

air compressor

What maintenance is required for air compressors?

Maintaining air compressors is essential to ensure their optimal performance, longevity, and safe operation. Regular maintenance helps prevent breakdowns, improves efficiency, and reduces the risk of accidents. Here are some key maintenance tasks for air compressors:

1. Regular Inspection: Perform visual inspections of the air compressor to identify any signs of wear, damage, or leaks. Inspect the compressor, hoses, fittings, and connections for any abnormalities. Pay attention to oil leaks, loose bolts, and worn-out components.

2. Oil Changes: If your air compressor has an oil lubrication system, regular oil changes are crucial. Follow the manufacturer’s recommendations for the frequency of oil changes and use the recommended oil type. Dirty or degraded oil can impact compressor performance and lead to premature wear.

3. Air Filter Cleaning or Replacement: Clean or replace the air filter regularly to ensure proper air intake and prevent contaminants from entering the compressor. Clogged or dirty filters can restrict airflow and reduce efficiency.

4. Drain Moisture: Air compressors produce moisture as a byproduct of the compression process. Accumulated moisture in the tank can lead to rust and corrosion. Drain the moisture regularly from the tank to prevent damage. Some compressors have automatic drains, while others require manual draining.

5. Belt Inspection and Adjustment: If your compressor has a belt-driven system, inspect the belts for signs of wear, cracks, or tension issues. Adjust or replace the belts as necessary to maintain proper tension and power transmission.

6. Tank Inspection: Inspect the compressor tank for any signs of corrosion, dents, or structural issues. A damaged tank can be hazardous and should be repaired or replaced promptly.

7. Valve Maintenance: Check the safety valves, pressure relief valves, and other valves regularly to ensure they are functioning correctly. Test the valves periodically to verify their proper operation.

8. Motor and Electrical Components: Inspect the motor and electrical components for any signs of damage or overheating. Check electrical connections for tightness and ensure proper grounding.

9. Keep the Area Clean: Maintain a clean and debris-free area around the compressor. Remove any dirt, dust, or obstructions that can hinder the compressor’s performance or cause overheating.

10. Follow Manufacturer’s Guidelines: Always refer to the manufacturer’s manual for specific maintenance instructions and recommended service intervals for your air compressor model. They provide valuable information on maintenance tasks, lubrication requirements, and safety precautions.

Regular maintenance is vital to keep your air compressor in optimal condition and extend its lifespan. It’s also important to note that maintenance requirements may vary depending on the type, size, and usage of the compressor. By following a comprehensive maintenance routine, you can ensure the reliable operation of your air compressor and maximize its efficiency and longevity.

China factory CHINAMFG GA Series Screw Air Compressor GA75VSD air compressor lowes
editor by CX 2023-10-06

China supplier Freezing Unit R22 CHINAMFG Zr380kc-Twd-522 31h CHINAMFG Scroll Parts Air Cooler Refrigeration Compressor in Stock supplier

Product Description

A variety of brands on sale

A total of 19 brands are on sale

Different types of compressors

Scroll refrigeration compressors are currently mainly in a fully enclosed structure, and are mainly used in air conditioners (heat pumps), heat pump hot water, refrigeration and other fields. The supporting downstream products include: household air conditioners, multi-split units, modular units, small water-to-ground source heat pumps, etc.

The advantages of our scroll compressors are

advantage:

1. There is no reciprocating mechanism, so the structure is simple, small in size, light in weight, less in parts (especially less in wearing parts), and high in reliability;

2. Small torque change, high balance, small vibration, stable operation, and small vibration of the whole machine;

3. It has high efficiency and frequency conversion speed regulation technology within the range of cooling capacity it adapts to;

4. The scroll compressor has no clearance volume and can maintain high volumetric efficiency operation

5. Low noise, good stability, high safety, relatively not easy to liquid shock.

Currently we sell various brands and types of compressors

Pecold refrigeration equipment is worth your choice

After-sales Service:	Provide Online Services
Warranty:	Provide Online Services
Installation Type:	Other
Lubrication Style:	Lubricated
Cylinder Position:	Other
Certification:	CE

Samples:	US$ 1000/Piece 1 Piece(Min.Order) \| Request Sample

Customization:	Available \|

air compressor

How does variable speed drive technology improve air compressor efficiency?

Variable Speed Drive (VSD) technology improves air compressor efficiency by allowing the compressor to adjust its motor speed to match the compressed air demand. This technology offers several benefits that contribute to energy savings and enhanced overall system efficiency. Here’s how VSD technology improves air compressor efficiency:

1. Matching Air Demand:

Air compressors equipped with VSD technology can vary the motor speed to precisely match the required compressed air output. Traditional fixed-speed compressors operate at a constant speed regardless of the actual demand, leading to energy wastage during periods of lower air demand. VSD compressors, on the other hand, ramp up or down the motor speed to deliver the necessary amount of compressed air, ensuring optimal energy utilization.

2. Reduced Unloaded Running Time:

Fixed-speed compressors often run unloaded during periods of low demand, where they continue to consume energy without producing compressed air. VSD technology eliminates or significantly reduces this unloaded running time by adjusting the motor speed to closely follow the air demand. As a result, VSD compressors minimize energy wastage during idle periods, leading to improved efficiency.

3. Soft Starting:

Traditional fixed-speed compressors experience high inrush currents during startup, which can strain the electrical system and cause voltage dips. VSD compressors utilize soft starting capabilities, gradually ramping up the motor speed instead of instantly reaching full speed. This soft starting feature reduces mechanical and electrical stress, ensuring a smooth and controlled startup, and minimizing energy spikes.

4. Energy Savings at Partial Load:

In many applications, compressed air demand varies throughout the day or during different production cycles. VSD compressors excel in such scenarios by operating at lower speeds during periods of lower demand. Since power consumption is proportional to motor speed, running the compressor at reduced speeds significantly reduces energy consumption compared to fixed-speed compressors that operate at a constant speed regardless of the demand.

5. Elimination of On/Off Cycling:

Fixed-speed compressors often use on/off cycling to adjust the compressed air output. This cycling can result in frequent starts and stops, which consume more energy and cause mechanical wear. VSD compressors eliminate the need for on/off cycling by continuously adjusting the motor speed to meet the demand. By operating at a consistent speed within the required range, VSD compressors minimize energy losses associated with frequent cycling.

6. Enhanced System Control:

VSD compressors offer advanced control capabilities, allowing for precise monitoring and adjustment of the compressed air system. These systems can integrate with sensors and control algorithms to maintain optimal system pressure, minimize pressure fluctuations, and prevent excessive energy consumption. The ability to fine-tune the compressor’s output based on real-time demand contributes to improved overall system efficiency.

By utilizing variable speed drive technology, air compressors can achieve significant energy savings, reduce operational costs, and enhance their environmental sustainability by minimizing energy wastage and optimizing efficiency.

air compressor

How do you maintain proper air quality in compressed air systems?

1. Air Filtration:

2. Moisture Control:

3. Oil Removal:

4. Regular Maintenance:

5. Air Receiver Tank Maintenance:

6. Air Quality Testing:

7. Education and Training:

8. Documentation and Record-Keeping:

By implementing these practices, compressed air systems can maintain proper air quality, minimize equipment damage, and ensure the integrity of processes that rely on compressed air.

air compressor

What are the key components of an air compressor system?

An air compressor system consists of several key components that work together to generate and deliver compressed air. Here are the essential components:

1. Compressor Pump: The compressor pump is the heart of the air compressor system. It draws in ambient air and compresses it to a higher pressure. The pump can be reciprocating (piston-driven) or rotary (screw, vane, or scroll-driven) based on the compressor type.

2. Electric Motor or Engine: The electric motor or engine is responsible for driving the compressor pump. It provides the power necessary to operate the pump and compress the air. The motor or engine’s size and power rating depend on the compressor’s capacity and intended application.

3. Air Intake: The air intake is the opening or inlet through which ambient air enters the compressor system. It is equipped with filters to remove dust, debris, and contaminants from the incoming air, ensuring clean air supply and protecting the compressor components.

4. Compression Chamber: The compression chamber is where the actual compression of air takes place. In reciprocating compressors, it consists of cylinders, pistons, valves, and connecting rods. In rotary compressors, it comprises intermeshing screws, vanes, or scrolls that compress the air as they rotate.

5. Receiver Tank: The receiver tank, also known as an air tank, is a storage vessel that holds the compressed air. It acts as a buffer, allowing for a steady supply of compressed air during peak demand periods and reducing pressure fluctuations. The tank also helps separate moisture from the compressed air, allowing it to condense and be drained out.

6. Pressure Relief Valve: The pressure relief valve is a safety device that protects the compressor system from over-pressurization. It automatically releases excess pressure if it exceeds a predetermined limit, preventing damage to the system and ensuring safe operation.

7. Pressure Switch: The pressure switch is an electrical component that controls the operation of the compressor motor. It monitors the pressure in the system and automatically starts or stops the motor based on pre-set pressure levels. This helps maintain the desired pressure range in the receiver tank.

8. Regulator: The regulator is a device used to control and adjust the output pressure of the compressed air. It allows users to set the desired pressure level for specific applications, ensuring a consistent and safe supply of compressed air.

9. Air Outlet and Distribution System: The air outlet is the point where the compressed air is delivered from the compressor system. It is connected to a distribution system comprising pipes, hoses, fittings, and valves that carry the compressed air to the desired application points or tools.

10. Filters, Dryers, and Lubricators: Depending on the application and air quality requirements, additional components such as filters, dryers, and lubricators may be included in the system. Filters remove contaminants, dryers remove moisture from the compressed air, and lubricators provide lubrication to pneumatic tools and equipment.

These are the key components of an air compressor system. Each component plays a crucial role in the generation, storage, and delivery of compressed air for various industrial, commercial, and personal applications.

China supplier Freezing Unit R22 CHINAMFG Zr380kc-Twd-522 31h CHINAMFG Scroll Parts Air Cooler Refrigeration Compressor in Stock supplier
editor by CX 2023-10-05

China supplier High-Tech Oilless Air Compressor with Movable Wheel for Dental Chair mini air compressor

Product Description

Quick Details		TY-3EW-120
Applicable Industries:	Medical & Dental	Showroom Location:	None
Condition:	New	Type:	PISTON
Configuration:	PORTABLE	Power Source:	AC POWER
Lubrication Style:	Oil-free	Mute:	Yes
Power Source:	AC POWER	Brand Name:	Toye
Lubrication Style:	Oil-free	Dimension(LWH):	100x45x76 CM
Place of Origin:	HangZhou ,China	Warranty:	2 Years
Voltage:	220V/110V	Air capacity:	450L/min
Weight:	105KGS	Video outgoing-inspection:	Provided
Working Pressure:	0.8 bar	Warranty of core components:	2 years
Machinery Test Report:	Provided	Gas Type:	Natural Gas
Marketing Type:	New products 2571	Usage:
Core Components:	Pressure vessel, Motor, Pump	VDC:	220V/110V
Product name:	Air compressor	Local Service Location:	NONE
Air delivery:	120L	Certification	CE,ISO13485
After Warranty Service:	Online and Offline services	Package	Carton/wooden box
After sales Service Provided:	Online and Offline services	Supply Ability	1000PCS/month

OIL FREE: Compare to lubrication compressor, one-step operation, do not need any lubricated oil, and harmless to the human body, more health and hygiene.

SUPER SILENT: Noise level lower than 60dB, ensure have friendly-enviromently treating room.

MULTI-PHASE FILTERATION: Advanced branded water filter to ensure extremely green and dry air.

EASY USING: One-step operation, when connecting with power, air compressor work automatic, also equipped with thermal prevention deviceto avoid over heating to protect motors.

GREEN AIR: Air tank have internal oxidation-proofed precess,avoaid corrosion and supply hygiene air to the equipments.

ENERGY SAVING: High quality pressure switch used to control the power of air compressor automatically stop when reach max pressure, and restart at mix pressure.

LOW VIBRATION: Robber foot reduce vibration and keep the air compressor away from wet place.

HIGH DURABILITY: long life air pump up to 3,000 hours working time.

SIMPLE OPERATION: No need to lubricate oil.

Applications:
Dental clinic, medical and health, SPA, Tattoo house, scientific research, electronic, chemical, Laboratory, spraying, Industrial, Printing etc.

More Design

Certifications

Company Profile

Exhibition

Production Workshop

Packaging & Shipping

Client Feedback

FAQ

1.Q:Are you a factory or trading company?

A:We are factory.we produce dental chair, dental intra oral camera and dental air compressor, and it’s approved CE certificated.

2.Q:Where is your factory located? How can I visit there?
A:Our factory is located in HangZhou City, ZheJiang Province, China, near HangZhou.You can fly to Xihu (West Lake) Dis. airport ,you can take tax or metro to HangZhou directly.All our clients, from home or abroad, are warmly welcome to visit us!

3.Q: How can I get Fob or C&F price?
A: Normally production time of products is from 2 week to 1 month depending on the quantity ordered. If you are sourcing a product, our representative will give you specific information regarding the lead time. If you need a rush order, contact our representatives to discuss your specific needs.

4.Q: How long is my warranty and what does it cover?
A:Detnal unit chair carry the full 1 year manufacturer warranty. Each warranty period begins at the date of delivery date and ends after 1 year.The warranty varies by option items and manufacturer All warranty claims will be void due to neglect, lack of maintenance, and/or improper handling.

5.How can I get the after sevice? How can I get the spare part after 1 year warranty?
A: We welcome your chats online (Chat or leave message: After service) or e-mail to us regarding any technical or related questions that you may have. And we will offer some free sparts for container order. We gurantee keep dental chair units spare parts offer.

If you want to know more information about our products welcome to contact us in any time, And welcome to our company!

Website: toyedent
Add: 5/F Zhisheng BLDG.,East Keji Rd.,Shishan Town,Xihu (West Lake) Dis. District, HangZhou

Interface:	1
Teeth Whitening Method:	Na
Applicable Departments:	Orthodontic Department
Certification:	ISO, CE
Type:	Piston
Material:	Metal

Samples:	US$ 165/Piece 1 Piece(Min.Order) \| Request Sample

Customization:	Available \|

air compressor

Can air compressors be used for painting and sandblasting?

Yes, air compressors can be used for both painting and sandblasting applications. Here’s a closer look at how air compressors are utilized for painting and sandblasting:

Painting:

Air compressors are commonly used in painting processes, especially in automotive, industrial, and construction applications. Here’s how they are involved:

Spray Guns: Air compressors power spray guns used for applying paint coatings. The compressed air atomizes the paint, creating a fine mist that can be evenly sprayed onto surfaces. The pressure and volume of the compressed air impact the spray pattern, coverage, and overall finish quality.
Paint Mixers and Agitators: Compressed air is often used to power mixers and agitators that ensure proper blending of paint components. These devices use the compressed air to stir or circulate the paint, preventing settling and maintaining a consistent mixture.
Airbrushing: Air compressors are essential for airbrushing techniques, which require precise control over airflow and pressure. Airbrushes are commonly used in artistic applications, such as illustrations, murals, and fine detailing work.

Sandblasting:

Blasting Cabinets: Air compressors power blasting cabinets or booths, which are enclosed spaces where the sandblasting process takes place. The compressed air propels the abrasive media, such as sand or grit, through a nozzle or gun, creating a forceful stream that impacts the surface being treated.
Abrasive Blasting Pots: Air compressors supply air to abrasive blasting pots or tanks that store and pressurize the abrasive media. The compressed air from the compressor enters the pot, pressurizing it and allowing for a controlled release of the abrasive material during the sandblasting process.
Air Dryers and Filters: In sandblasting applications, it is crucial to have clean, dry air to prevent moisture and contaminants from affecting the abrasive blasting process and the quality of the surface being treated. Air compressors may be equipped with air dryers and filters to remove moisture, oil, and impurities from the compressed air.

Proper safety measures, such as wearing protective gear and following established protocols, should always be followed when working with air compressors for painting and sandblasting applications.

air compressor

How do you choose the right air compressor for woodworking?

1. Required Air Volume (CFM):

2. Tank Size:

3. Maximum Pressure (PSI):

4. Noise Level:

5. Portability:

6. Power Source:

7. Quality and Reliability:

8. Budget:

air compressor

Are there portable air compressors available for home use?

6. Noise Level: Portable air compressors designed for home use often prioritize low noise levels. They are engineered to operate quietly, reducing noise disturbances in residential environments.

China supplier High-Tech Oilless Air Compressor with Movable Wheel for Dental Chair mini air compressor
editor by CX 2023-10-05